Share Your Innovations

[NICKWORN]

So I got this idea from a local kayaker here in SD.. Dylan Pierce. It's a conduit and a few pvc fittings. Using my Hook 5 Transducer in the duct seal application seemed to be hampering my readings. So I gave this a try.

Took the conduit and some pvc fittings to make this water tight floating transducer mount. My transducer fit snug on the inside and now sets in water without the interference of anything except the actually hull itself. Going to be trialing it this weekend but when testing in garage I was actually able to here the transducers ping as I couldn't before when placed in a pancake of duct seal
I also placed the transducer right under my center hatch for easy access if somehow the water would need to be refilled.

I can't seem to think why this wouldn't be the best option beside having a newer hobie with the prefab transducer mount.

All in all $15, marine goop and conduit being the bulk of the price.

P.S. I used marine goop on the bottom edge to seal and then the left over duct seal I pulled from old application to reinforce the conduit to the yak for those bumpy road trips and swells.


Thoughts?

[dsafety]

That is a very elegant solution for a water mount. In my experience, the seal to the hull eventually fails and the water leaks out. Your design may not have that problem because you have attached the housing to a spot that does not appear to have much flex or curvature.

Should the seal ever fail, you might consider replacing the water with marine grease. It transmits the signal as well as water and will not leak out even if the kayak is stored upside down for months at a time.

[jruiz]

Originally Posted by NICKWORN

So I got this idea from a local kayaker here in SD.. Dylan Pierce. It's a conduit and a few pvc fittings. Using my Hook 5 Transducer in the duct seal application seemed to be hampering my readings. So I gave this a try.

Took the conduit and some pvc fittings to make this water tight floating transducer mount. My transducer fit snug on the inside and now sets in water without the interference of anything except the actually hull itself. Going to be trialing it this weekend but when testing in garage I was actually able to here the transducers ping as I couldn't before when placed in a pancake of duct seal
I also placed the transducer right under my center hatch for easy access if somehow the water would need to be refilled.

I can't seem to think why this wouldn't be the best option beside having a newer hobie with the prefab transducer mount.

All in all $15, marine goop and conduit being the bulk of the price.

P.S. I used marine goop on the bottom edge to seal and then the left over duct seal I pulled from old application to reinforce the conduit to the yak for those bumpy road trips and swells.


Thoughts?

So before you had hull, duct seal, then transducer. Now you have hull, duct seal, conduit, some water, then transducer. I'm having a hard time convincing myself that it's better. I think the next best thing to a transducer ready setup is a transducer mounted to the hull with a container around the transducer that you fill with water. What material is that conduit? Looks like painted/epoxied steel.

[NICKWORN]

Originally Posted by jruiz

So before you had hull, duct seal, then transducer. Now you have hull, duct seal, conduit, some water, then transducer. I'm having a hard time convincing myself that it's better. I think the next best thing to a transducer ready setup is a transducer mounted to the hull with a container around the transducer that you fill with water. What material is that conduit? Looks like painted/epoxied steel.

The conduit is plastic, not sure what kind, but the marine goop is only on the bottom edge of the conduit( which has the bottom taken off ), and the duct seal is only used in the edges of the outside so there is nothing interfering with the pinging of the transducer besides the plastic hull of the kayak! Not sure what you are talking about maybe u missed understood my description.

[jruiz]

Originally Posted by NICKWORN

The conduit is plastic, not sure what kind, but the marine goop is only on the bottom edge of the conduit( which has the bottom taken off ), and the duct seal is only used in the edges of the outside so there is nothing interfering with the pinging of the transducer besides the plastic hull of the kayak! Not sure what you are talking about maybe u missed understood my description.

I see, I mistakenly assumed that the transducer was fully enclosed in the conduit.

[NICKWORN]

Originally Posted by jruiz

I see, I mistakenly assumed that the transducer was fully enclosed in the conduit.

Yea I thought so.