![]() |
|
Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Community | Calendar | Today's Posts | Search |
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
"Floater"
Join Date: Sep 2010
Location: so cal
Posts: 164
|
Hobie battery box
I decided to engineer a new box for my outback for the rear 8" hatch since it doesn't get used for anything else. I was using the dry bag method up to now.
All that's needed is a CNC router, Hand held router, table saw, 1/2" and 1/4" ABS plastic, ABS glue and some basic dimensions. Directions; For the rounded part; Program the router using master cam, load drawing into CNC machine operating software. Adhere the 1/2" sheet of ABS to the router. Push the go button. Wait a couple minutes, remove plastic from router. (The round hole in the top serves two purposes; one is to route the power cable, the other is a finger hole to lift it out.) Cut squared pieces to proper dimensions using the table saw. Glue it all together with ABS glue. Let sit for 24 hours to cure. Use the hand router to round off the top edge of the box. The box should fit any Hobie with 8" round hatches. The battery I use is a 12 volt, 14AH. Slightly larger than typical but I can run my FF/GPS for about 3 days without a charge if necessary. If you use a typical battery with the box I made, you can put your keys and wallet in it too. Last edited by Kaijuu; 03-22-2011 at 07:01 AM. |
![]() |
![]() |
![]() |
#2 |
Team Keine Zugehörigkeit
Join Date: Nov 2010
Location: Way out there
Posts: 2,854
|
Hay Kaijuu, being that not everyone here has MC and a CNC or those that do only cut metal, would you consider selling a box or two?
__________________
Não alimente os trolls------------Don't feed the trolls---------------インタネット荒らしを無視しろ ![]() |
![]() |
![]() |
![]() |
#3 |
"Floater"
Join Date: Sep 2010
Location: so cal
Posts: 164
|
a box or two
I suppose anything is possible. You should probably check it out first.
Variations are also manageable in most any material. For the Yak, plastic rules; It doesn't oxidize. Any other ideas that need a build, let me know. I live in Vista but go to Oceanside most days unless rain. I can bring it with me. P.S. We can also design and build your CNC router, then you wont need me to build a box. P.S.S. this box can be made using hand tools. A table saw, router, jig saw and a drill. Last edited by Kaijuu; 03-22-2011 at 07:03 AM. |
![]() |
![]() |
![]() |
#4 |
Team Keine Zugehörigkeit
Join Date: Nov 2010
Location: Way out there
Posts: 2,854
|
I have access to all the necessary tooling and machines, but our least expensive CNC runs at $11.00 per minute, yes I typed PER MINUTE. the boss might go ape ca-ca
![]() Pm me what you have to offer as far as a router. I have been looking at the Taig Micro mill for some time now but just cant pull the trigger.
__________________
Não alimente os trolls------------Don't feed the trolls---------------インタネット荒らしを無視しろ ![]() Last edited by bus kid; 03-22-2011 at 08:51 AM. Reason: typo correction |
![]() |
![]() |
![]() |
#6 |
"Floater"
Join Date: Sep 2010
Location: so cal
Posts: 164
|
best to call.
Its best just to PM me. Keith
Last edited by Kaijuu; 03-22-2011 at 06:34 PM. |
![]() |
![]() |
![]() |
#7 |
Currently @ MLO Territory
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
|
Well after i got tired of seeing all my junk all over the garage, i sat down and doodle some possible way i can store my kayak in the garage. I only could mount the kayak straight on from a perpendicular point since i have one side of the garage for my kayaks to fit. I decided to make a wood frame and use PVC as my rack holders. The first bottom portion is to store all the other junk you have in your garage the second layers is for your fishing bag, batteries then comes the PVC. The top PVC come loose to remove the bottom kayak.
![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#8 | |
Senior Member
Join Date: Mar 2010
Location: San Diego
Posts: 2,385
|
Quote:
__________________
No better time than being on the water, God Bless, JimmyZ ![]() |
|
![]() |
![]() |
![]() |
#9 |
"Floater"
Join Date: Sep 2010
Location: so cal
Posts: 164
|
Battery Box Storage / Tackle box update
I've been playing around with the idea of the original battery box. I have since made someone a larger box for his Revos' rear hatch to store both his FF and Live well batteries.
Today I decided to work the large box into a storage/tackle box to fit the middle hatch of my Outback. It's close to 7" deep with a tray that slips inside and sits at the top. The tray slips in and out easily. Figured I would put small terminal tackle in the tray and the larger stuff inside the larger compartment at the lower end. Still working things out. I guess now I'll have to do the Sea trials. One thing I'm unsure of is if the ABS is going to react with my plastic swim-baits. I remember the old plastic worms would melt some of the plastics used in tackle boxes and trays. Last edited by Kaijuu; 03-28-2011 at 03:20 PM. |
![]() |
![]() |
![]() |
Tags |
kayak fishing inovations, kayak rigging ideas |
|
|